Data Communication & its Modes

Data Communication 
The distance over which data moves within a computer may vary from a few thousandths of an inch, as is the case within a single IC chip, to as much as several feet along the backplane of the main circuit board. Over such small distances, digital data may be transmitted as direct, two-level electrical signals over simple copper conductors. Except for the fastest computers, circuit designers are not very concerned about the shape of the conductor or the analog characteristics of signal transmission.

Frequently, however, data must be sent beyond the local circuitry that constitutes a computer. In many cases, the distances involved may be enormous. Unfortunately, as the distance between the source of a message and its destination increases, accurate transmission becomes increasingly difficult. This results from the electrical distortion of signals traveling through long conductors, and from noise added to the signal as it propagates through a transmission medium. Although some precautions must be taken for data exchange within a computer, the biggest problems occur when data is transferred to devices outside the computer's circuitry. In this case, distortion and noise can become so severe that information is lost.

Data Communications concerns the transmission of digital messages to devices external to the message source. "External" devices are generally thought of as being independently powered circuitry that exists beyond the chassis of a computer or other digital message source. As a rule, the maximum permissible transmission rate of a message is directly proportional to signal power, and inversely proportional to channel noise. It is the aim of any communications system to provide the highest possible transmission rate at the lowest possible power and with the least possible noise.

Communication Modes

Simplex communication refers to communication that occurs in one direction only. Two definitions have arisen over time: a common definition, which is used in ANSI standard and elsewhere, and an ITU-T definition. The ITU definition of simplex is termed "half duplex" in other contexts.

According to the ANSI definition, a simplex circuit is one where all signals can flow in only one direction. These systems are often employed in broadcast networks, where the receivers do not need to send any data back to the transmitter/broadcaster.[edit]ANSI definition: One way signaling

Examples

• Commercial radio broadcast (not walkie-talkies, etc.)
• Television broadcast
• Keyboard to CPU communication
• Internet multicast
• One-way communications from a launcher to a guided missile, where the launcher (airplane, ship, etc.) sends commands to the missile, but does not receive any information sent back.

ITU-T definition: One way signaling at a time

According to the ITU-T definition, a simplex circuit is one where signals can flow in only one direction at a time. At other times communications can flow in the reverse direction. A more common term for this application is half-duplex.

The old Western Union company used the term simplex when describing the half-duplex and simplex capacity of their newtransatlantic telegraph cable completed between Newfoundland and the Azores in 1928. The same definition for a simplex radio channel was used by the National Fire Protection Association in 2002. 

Half-duplex

A simple illustration of a half-duplex communication system

A half-duplex (HDX) system provides communication in both directions, but only one direction at a time (not simultaneously). Typically, once a party begins receiving a signal, it must wait for the transmitter to stop transmitting, before replying (antennas are of trans-receiver type in these devices, so as to transmit and receive the signal as well).

An example of a half-duplex system is a two-party system such as a "walkie-talkie" style two-way radio, wherein one must use "Over" or another previously designated command to indicate the end of transmission, and ensure that only one party transmits at a time, because both parties transmit and receive on the same frequency.

A good analogy for a half-duplex system would be a one-lane road with traffic controllers at each end. Traffic can flow in both directions, but only one direction at a time, regulated by the traffic controllers.

In automatically run communications systems, such as two-way data-links, the time allocations for communications in a half-duplex system can be firmly controlled by the hardware. Thus, there is no waste of the channel for switching. For example, station A on one end of the data link could be allowed to transmit for exactly one second, and then station B on the other end could be allowed to transmit for exactly one second. And then this cycle repeats over and over again.

Full-duplex

A simple illustration of a full-duplex communication system. Full-duplex is not common in handheld radios like shown here due to the cost and complexity of common duplexing methods.

A full-duplex (FDX), or sometimes double-duplex system, allows communication in both directions, and, unlike half-duplex, allows this to happen simultaneously. Land-line telephone networks are full-duplex, since they allow both callers to speak and be heard at the same time. A good analogy for a full-duplex system would be a two-lane road with one lane for each direction.

Examples: Telephone, Mobile Phone, etc.

Two-way radios can be, for instance, designed as full-duplex systems, which transmit on one frequency and receive on a different frequency. This is also called frequency-division duplex. Frequency-division duplex systems can be extended to farther distances using pairs of simple repeater stations, because the communications transmitted on any one frequency always travel in the same direction.

Full-duplex Ethernet connections work by making simultaneous use of two physical pairs of twisted cable (which are inside the jacket), wherein one pair is used for receiving packets and one pair is used for sending packets (two pairs per direction for some types of Ethernet), to a directly connected device. This effectively makes the cable itself a collision-free environment and doubles the maximum data capacity that can be supported by the connection.

There are several benefits to using full-duplex over half-duplex. First, time is not wasted, since no frames need to be retransmitted, as there are no collisions. Second, the full data capacity is available in both directions because the send and receive functions are separated. Third, stations (or nodes) do not have to wait until others complete their transmission, since there is only one transmitter for each twisted pair.

Historically, some computer-based systems of the 1960s and 1970s required full-duplex facilities even for half-duplex operation, because their poll-and-response schemes could not tolerate the slight delays in reversing the direction of transmission in a half-duplex line.